Resettable Pistonless Barrel Shift Register

A shift register moves an active redstone signal down a line of outputs one step at a time with every input pulse. This silent, pistonless barrel design uses locked repeaters to hold the state, automatically loops the signal back to the start, and includes a dedicated reset line to clear and return the register to the first bit at any point.

Memory CircuitsAdvancedJava Edition
Resettable Pistonless Barrel Shift Register video tutorial

Video: Resettable Redstone Shift Register by Scatterbrain

How to build it

  1. Build the Main Repeater Chain

    Place an alternating line of 8 repeaters and 8 solid blocks in a row (for an 8-bit register). Leave the space directly beneath the solid blocks clear if you plan to route outputs from underneath later.

  2. Add the Locking Repeaters

    Along one side of your main line, place a row of repeaters facing directly into the side of each main repeater to lock them. Run a line of redstone dust behind all of the locking repeaters except the very first one.

  3. Power the Lock Line

    Place a solid block with a redstone torch attached to it to power the redstone dust line behind the locking repeaters. Wire the first locking repeater so it is powered alongside the rest of the lock line, keeping all 8 bits locked by default.

  4. Build the Shift Pulse Generator

    Behind the block holding the locking torch, build a 1-tick pulse generator. Place a comparator in subtract mode feeding towards the torch block, and run a repeater set to 2 ticks into the side of the comparator with a loop of redstone dust connecting its input and back side.

  5. Add the Input Comparator

    Place a comparator in subtract mode feeding directly into the very first repeater of your main shift register line. This controls when a new signal enters the first bit.

  6. Tap the First 7 Bits

    On the open side of the main register line, place a solid block with redstone dust on top next to each of the first 7 output blocks. Leave the 8th (final) block empty so the register knows when to wrap around.

  7. Create the Upper Slab Shelf

    Build a raised shelf of top slabs above the 7 dust blocks and run redstone dust across the entire shelf. Because redstone travels up slabs but cannot travel back down, any active bit from 1 to 7 will power the shelf without back-charging the rest of the bits.

  8. Connect the Feedback Lock

    At the start of the slab shelf, place a repeater feeding into a solid block to carry the signal into the side of the subtract comparator at the register's entrance. While any of the first 7 bits are lit, this feedback line cancels the entrance comparator so only one bit remains active.

  9. Wire the Reset Torch

    Above the entrance wiring, add a second redstone torch arrangement and run a redstone dust line from your reset input so that pressing the reset button powers both torch blocks simultaneously, unlocking the register line.

  10. Build the Reset Pulse Generator

    Construct a 2x3 upper platform for the reset logic, using a top slab for one corner. On that slab, place a subtract-mode comparator facing outward, with a repeater set to 3 ticks feeding into its side and dust looping around to create a falling-edge pulse generator.

  11. Connect the Reset Generator to the Input

    Have the upper reset comparator hard-power a solid block with redstone dust alongside it so the signal steps down the slab into the main input system below. Place your Shift and Reset buttons along with Redstone Lamps on each output block to test.

How it works

This circuit relies on repeater locking and one-way slab wiring to shift a single bit down a chain without pistons:

  • Repeater Locking: Each bit in the register is a repeater feeding into a solid block. A perpendicular repeater powered by a redstone torch locks every stage, freezing its current state (on or off).
  • Shifting (1-Tick Pulse): Pressing the shift button sends a pulse through a subtract-mode comparator with a 2-tick repeater feeding its side. This shortens the signal into a precise 1-tick pulse that briefly turns off the locking torch. All repeaters unlock for 1 redstone tick, advancing the active signal by exactly one block before re-locking.
  • Barrel Feedback & Slab Diode: An upper line of redstone dust on top slabs reads the state of bits 1 through 7. Because signals can travel diagonally up onto a top slab but not back down, the slab shelf acts as a massive OR gate without cross-powering the inactive outputs. As long as any of the first 7 bits is on, the shelf subtracts from the input comparator, preventing a new bit from entering. When the signal reaches the 8th bit (or when the register is empty), the shelf turns off and allows the next shift pulse to inject a fresh bit at position 1.
  • Resetting: Pressing the reset button turns off the locking torch long enough to flush the entire repeater chain while the upper falling-edge generator waits until the line is clear before injecting a fresh signal into the very first bit.

Tips & variations

  • Reset Pulse Length: The reset pulse must stay active for at least as many redstone ticks as your shift register is long (e.g., at least 8 ticks for an 8-bit register) so that any active bit has enough time to travel all the way out of the chain.
  • Scaling the Register: You can make this register shorter or longer (such as 4-bit for a calculator). No matter the length, always leave the very last bit disconnected from the upper slab feedback shelf.
  • Taking Outputs: You can pull signals from below the solid blocks between repeaters using redstone dust, or place redstone torches on top of the output blocks (with inverted stairs or blocks above them) to read inverted outputs vertically.

Frequently asked questions

Why do we use slabs on the feedback line above the register?
Top slabs act as one-way diodes for redstone dust. The signal can jump up onto the slab shelf from any active bit below, but it cannot travel back down into the other unpowered bits.
Why is the last bit left off the slab feedback line?
Leaving the last bit disconnected causes the feedback lock to turn off when the signal reaches the end of the line. On the very next shift pulse, the entrance comparator is unlocked so a new signal wraps around into the first bit.
How fast of an input pulse can the shift line take?
Because the built-in comparator pulse generator converts the input into a 1-tick pulse, you can trigger the shift input with either a standard button or a much faster 1- or 2-tick redstone pulse.

Components used

More register / shift register