1-Wide Instant NOT Gate

Standard redstone torch NOT gates add a 1-tick delay to your circuits, which can slow down large technical builds. This compact 1-wide instant NOT gate uses sticky pistons and redstone blocks to invert a signal with zero delay on both the rising and falling edges. It is ideal for instant-wire networks, fast logic processors, and long-distance instant repeaters.

Logic GatesIntermediateJava Edition
1-Wide Instant NOT Gate video tutorial

Video: Minecraft Redstone Tutorial - 1.5 Snapshot Instant Not Gate by TT Lemon

How to build it

  1. Place the Input and Primary Piston

    Set down your input block with a lever attached and run redstone dust to a downward-facing sticky piston. Attach a Block of Redstone to the face of this piston so it rests above your output line.

  2. Wire the Output Line

    Run your output redstone dust line directly adjacent to the resting position of the Block of Redstone. Note that the input and output lines in this compact design sit at slightly different vertical levels.

  3. Add the Delay Repeater

    Branch off your main input line and place a Redstone Repeater running toward the output side. Set this repeater to 4 ticks so it can hold the signal during the reset phase.

  4. Install the Cutoff Piston

    Place a second sticky piston holding a solid building block arranged so that when triggered by the first piston's movement, it pushes the solid block down to cut off the wire coming from the 4-tick repeater.

  5. Test and Optional Speed Upgrade

    Flip the lever on and off to verify the output changes state immediately both ways. If you need the circuit to handle faster consecutive input pulses, bridge a line of redstone dust across the top (making it 1 block taller) and reduce the repeater delay to 2 ticks.

How it works

This circuit achieves zero-tick inversion on both the rising and falling edges by combining instant piston retraction with a timed signal cutoff:

  • Turning the Input ON (Output OFF): When the input is powered, the first sticky piston immediately starts pushing the Block of Redstone out of position. Because a moving redstone block stops providing power the exact game tick it begins moving, the output wire turns off instantly. Meanwhile, the input signal enters the 4-tick Redstone Repeater, but before that signal can pass through to the output, the two pistons finish extending and push a solid block down to sever the repeater's output wire.
  • Turning the Input OFF (Output ON): When the input turns off, the cutoff piston immediately begins retracting the solid block that was cutting the wire.The moment a solid block starts moving, it becomes transparent to redstone signals, instantly allowing the power still stored in the 4-tick repeater to jump through and turn the output ON. The 4-tick repeater holds the output line powered just long enough for the first sticky piston to finish pulling the Block of Redstone back into its resting spot, smoothly taking over the power supply without any flicker.

Tips & variations

  • Repeater Timing: In the standard 1x5x4 build, the repeater must be set to 4 ticks. If you set it to 2 ticks, the two chained pistons will not move the cutoff block into place fast enough when turning the input on, causing a brief pulse or glitch in the output.
  • Faster Reset Variant: Because of the 4-tick repeater and chained piston trigger, spamming the input too quickly can break the cycle. You can fix this by running a direct redstone line across the top to trigger both pistons simultaneously. This adds 1 block to the height (1x6x4) but lets you lower the repeater to 2 ticks, doubling the recovery speed between toggles.
  • Level Offset: Keep in mind that the input and output lines are on different vertical levels, so you may need to step your redstone wire up or down when fitting it into long transmission lines.

Frequently asked questions

Why does my output flicker when I turn the input on?
Your repeater delay is set too low. In the compact 4x5 version, the second piston relies on the first piston finishing its movement before cutting the wire, so the repeater must be on 4 ticks to prevent the signal from sneaking through early.
How can I make the gate accept faster inputs?
Run a redstone line over the top of the circuit so the input powers both sticky pistons directly at the same time, then reduce the repeater from 4 ticks to 2 ticks.
Does this instant NOT gate work in Bedrock Edition?
No, this design was built for Java Edition (introduced in the 1.5 snapshots) and relies on Java's specific zero-tick piston retraction and transparent moving-block mechanics.

Components used

More not gate