Flashing Lights

This classic redstone tutorial shows how to build a row of flashing lights that automatically turn on and off in a chasing sequence. It relies only on solid building blocks, redstone dust, and redstone torches to create homemade inverters and repeaters. Use this circuit to decorate hallways, runways, dance floors, or warning displays in your survival base.

Displays & LightingBeginnerJava Edition
Flashing Lights video tutorial

Video: Minecraft tutorial: Flashing lights - Remade by Ajnscape

How to build it

  1. Build the Main Power Inverter

    Place a solid block on the ground and attach a redstone torch to its forward-facing side. Run a piece of redstone dust into the back or directly on top of that block so incoming power will turn the torch off.

  2. Understand the Torch Repeater Module

    Before looping the clock, learn the two-torch repeater unit: place a block with a redstone torch on its side, run redstone dust into a second block, and place another torch on the side or top of that second block. This double-inverts the signal to keep the same state while adding two ticks of delay.

  3. Chain Four Torch Repeaters Together

    From the output of your first power inverter, build a line of four two-torch repeaters in series. Having four repeaters plus the initial inverter slows the signal down enough that the torches will not burn out.

  4. Close the Clock Loop

    Connect the redstone dust output from the fourth repeater back around into the input of your very first power inverter. Because there are an odd number of inversions in the loop (nine torches total), the signal will immediately begin pulsing on and off around the track.

  5. Branch Out to Your Display Lights

    Run a redstone output line from the clock toward your row of display lights (which use redstone torches as the light source). Place a two-torch repeater between every single light branch along the row.

  6. Connect the Sequential Light Branches

    Wire each individual light branch off the main line after each repeater delay. Even though redstone dust can travel 15 blocks, placing a repeater before every branch ensures each light flashes at a slightly different time for a smooth chasing wave effect.

How it works

This circuit works by combining two fundamental classic redstone concepts: the NOT gate (inverter) and the two-torch repeater.

  • Power Inverter: A redstone torch attached to a block turns off whenever that block is powered from the back or top. When no power goes in, the torch outputs power; when power goes in, the torch turns off.
  • Two-Torch Repeater: Placing two inverters back-to-back inverts the signal twice. If power goes in, the first torch turns off, allowing the second torch to turn back on. This restores the original signal while adding a short delay.
  • 9-Torch Loop Clock: If you wire a single inverter directly into itself—or use only one repeater—the torch switches states too fast and burns out. By chaining one inverter with four two-torch repeaters (9 torches total, an odd number of inversions), the pulse takes long enough to travel around the loop that it creates a stable, continuous flashing clock.
  • Sequential Display: Tapping the clock signal and placing a repeater between every light branch staggers the pulse arrival time, causing the lights to turn on and off in a row.

Tips & variations

  • Preventing Torch Burnout: Never connect an inverter directly back into itself with fewer than four homemade repeaters (or sufficient delay), or the redstone torches will hiss, smoke, and burn out.
  • Modern Compact Upgrade: This tutorial uses classic redstone torch repeaters. In modern versions of Minecraft, you can replace each two-torch repeater module with a single craftable Redstone Repeater block and use Redstone Lamps for the lights to save massive amounts of space.
  • Adjusting Speed: To make the lights flash slower, add more two-torch repeaters into the main clock loop. always keeping one extra inverter so the total number of redstone torches in the loop remains odd.

Frequently asked questions

Why do my redstone torches keep smoking and turning off?
Your clock loop is too short. A redstone torch burns out if it is forced to flip on and off too rapidly. Make sure you have at least four two-torch repeaters plus your starting inverter in the loop.
Why do I need a repeater between every light if redstone reaches 15 blocks?
Redstone dust transmits power almost instantly across all 15 blocks, which would make all your lights flash at the exact same time. Putting a repeater between every branch adds a delay so the lights flash one after another in a row.
Does the input wire have to go on top of the inverter block?
No, you can run the redstone dust either directly into the back face of the block holding the torch or place it on top of that block—both will properly invert the signal.

Components used

More light show