Static Wind Charge Generator

A static wind charge generator uses a captured Breeze aggroed onto an Iron Golem to infinitely produce and store wind charges in a single block space. By aligning and holding these projectiles in stasis, you can create a customizable payload to launch players hundreds of blocks into the air or fire concentrated wind blasts horizontally. This design is specifically engineered to work around Minecraft Bedrock Edition mechanics where Java note block setups fail.

TNT & CannonsAdvancedBedrock Edition
Static Wind Charge Generator video tutorial

Video: Bedrock Static Wind Charge Generator | Minecraft by Dragong

How to build it

  1. Build the Breeze and Golem Enclosures

    Create two secure cages aligned with each other: one to hold a captured Breeze and another a short distance away to hold an Iron Golem as a target. Leave a clear line of sight between them that runs through a stair and wall alignment gap.

  2. Install the Line-of-Sight Cutoff Piston

    Place a piston directly above the Breeze's head. When extended downward, this piston blocks the Breeze's vision so it stops firing at the Iron Golem.

  3. Set Up the Crafter Control Panel (Alternate Vertical Version)

    For the basic vertical launcher variant, place a Crafter read by a Redstone Comparator leading to the cutoff piston and an Iron Trapdoor above the stasis spot. Toggling 1 slot powers the piston to stop the Breeze, while toggling 3 slots opens the trapdoor so you can stand on top and punch the stored charges to launch upwards.

  4. Construct the Projectile Alignment Chamber (v3.0)

    For the advanced directional version (orange circuit), place stairs and wall blocks along the firing path between the Breeze and Golem. Position pistons to push and align the incoming wind charges vertically into a single stasis point without popping them.

  5. Wire the On/Off Toggle Circuit

    Build the activation toggle (yellow circuit) connected to the piston above the Breeze. Turning the machine on retracts the block, allowing the Breeze to see the Iron Golem and begin generating wind charges.

  6. Add the Dropper-Hopper Payload Counter

    Below the alignment area, build the item counter (light blue circuit) using a dropper facing into a hopper with a comparator readout. Load items into the dropper equal to double the number of wind charges you want stored (for example, 20 items equals a payload of 10 wind charges).

  7. Connect the Observer Detection Line

    Place an observer watching a solid component like a dropper rather than a flashing redstone lamp or bare dust. Each time the alignment pistons cycle to store a wind charge, the observer pulses the dropper counter.

  8. Install the Water Dispenser and Reset System

    Finish with the firing and reset mechanism (dark blue circuit) using a dispenser loaded with a water bucket near the stasis chamber. Make sure the observer trigger block (the dropper) blocks the water stream from spilling into your redstone dust, allowing the system to cleanly release the payload and reset the counter.

How it works

The generator exploits mob aggression between a Breeze and an Iron Golem. Because the Breeze cannot traverse its enclosure, it repeatedly shoots wind charges toward the Golem through the narrow gap provided by stairs and walls.

  • Line of Sight Control: A piston pushes a block over the Breeze's head to break line of sight when the machine is turned off or once the desired payload count is reached.
  • Crafter Signal Strength (Vertical Variant): In the simpler vertical launcher, selecting internal slots inside a Crafter changes the signal strength read by a Redstone Comparator. Strength 1 closes the Breeze chamber, while strength 3 opens the top Iron Trapdoor for player launching.
  • Alignment & Stasis (v3.0): Pistons push the moving wind charges into a precise sub-block alignment against stairs/walls where their velocity is halted, suspending them in stasis.
  • Payload Counting: Every cycle of the alignment pistons triggers an Observer watching a Dropper. The counter dropper transfers items into a Hopper at a 2:1 ratio (2 items per 1 wind charge). Once all items transfer, the comparator cuts off the Breeze and triggers the water dispenser system to release or reset the chamber.

Tips & variations

  • Fixing Golem Hits: Occasionally the Breeze's alignment may glitch in Bedrock and its shots will start directly hitting the Iron Golem. If this happens, simply save, exit, and relog into the world to reset the mob's firing alignment.
  • Block the Water Flow: Do not replace the observer's target dropper with plain redstone dust. A full block like a dropper is required there both to avoid annoying flashing light from a redstone lamp and to physically block the dispensed water from washing away your wiring.
  • Vertical Player Launching: When using the vertical trapdoor design, align yourself carefully on the edge before opening the trapdoor and do not crouch (shift) when punching the wind charge cluster—around 10+ charges can easily launch you over 240 blocks straight up.
  • Bedrock vs. Java: This setup is custom-built for Bedrock Edition because standard Java wind charge stasis designs rely on Note Block update behaviors that do not function the same way in Bedrock.

Frequently asked questions

How do you control how many wind charges are stored in one shot?
Adjust the number of items inside the counter dropper. The counter uses a 2:1 ratio, meaning every 2 items you put in the dropper will store 1 wind charge (e.g., 20 items = 10 wind charges).
Why is the Breeze hitting the Iron Golem instead of storing the wind charges?
In Minecraft Bedrock, mob projectile alignment can occasionally desync. Leaving the world and logging back in will fix the Breeze's aim and make the machine quiet again.
How high can the vertical wind charge stasis launcher boost you?
Punching a small cluster of stored wind charges through the iron trapdoor can easily blast a survival player around 230 to 245 blocks straight up into the air.

Components used

More launcher