
Video: How to Build Any Song with Note Blocks in Minecraft by FCD Games
How to build it
- Build the Silent Starter Trigger
Place one note block on the ground with a solid building block directly on top of it to mute its sound. Place an observer facing the side of that note block so it detects when you right-click it, and put a piece of redstone dust behind the observer's output.
- Lay Out the First Row of Instrument Blocks
Starting from your trigger dust, place a line of Emerald Blocks (which give an 8-bit chiptune sound) with a 1-block gap between each one. In the survival Tetris example, you will place 20 Emerald Blocks in total across four snaking rows.
- Connect the Rows with Repeaters
Place a redstone repeater in every 1-block gap between your Emerald Blocks. Make sure the repeaters all face along the path of the circuit so the signal travels forward from the trigger.
- Snake the Corners with Redstone Dust
When you reach the end of a row, turn the line back in the opposite direction to keep the footprint compact. Use 3 pieces of redstone dust and a repeater at each turn to bridge the signal into the next parallel row.
- Place the Note Blocks
Place one Note Block directly on top of each of the 20 Emerald Blocks. Make sure there is empty air above every melody note block so they are not muted.
- Tune the First Phrase (Measure 1)
Right-click the first six note blocks to set their pitches and adjust the repeaters between them (1 dash = 1 repeater tick): click Note 1 (22 times), set Repeater to 4 ticks; Note 2 (17 clicks), Repeater 2 ticks; Note 3 (18 clicks), Repeater 2 ticks; Note 4 (20 clicks), Repeater 4 ticks; Note 5 (18 clicks), Repeater 2 ticks; Note 6 (17 clicks), Repeater 2 ticks.
- Tune the Second Phrase (Measure 2)
Continue along the snake for the next six notes: Note 7 (15 clicks), Repeater 4 ticks; Note 8 (15 clicks), Repeater 2 ticks; Note 9 (18 clicks), Repeater 2 ticks; Note 10 (22 clicks), Repeater 4 ticks; Note 11 (20 clicks), Repeater 2 ticks; Note 12 (18 clicks), Repeater 2 ticks.
- Tune the Final Phrases (Measures 3 & 4)
Finish tuning the remaining eight notes: Note 13 (17 clicks), Repeater 4 ticks; Note 14 (17 clicks), Repeater 2 ticks; Note 15 (18 clicks), Repeater 2 ticks; Note 16 (20 clicks), Repeater 4 ticks; Note 17 (22 clicks), Repeater 4 ticks; Note 18 (18 clicks), Repeater 4 ticks; Note 19 (15 clicks), Repeater 4 ticks; and Note 20 (15 clicks).
How it works
This circuit translates musical sheet notation directly into redstone timing and block pitches:
- Silent Observer Starter: Placing a solid block above a note block prevents it from playing a sound, but right-clicking it still causes a block state change. The
Observerdetects this update and emits a crisp 1-tick redstone pulse to start the song without button click noise. - Tempo & Rhythm (Repeater Ticks): Minecraft processes 10 redstone ticks per second. At a standard 150 BPM (beats per minute), a sixteenth note equals
1 redstone tick, an eighth note equals2 redstone ticks, and a quarter note (one full beat) equals4 redstone ticks. Adjusting each repeater's delay controls how long a note rings before the next one fires. - Instrument & Powering: Repeaters strongly power the Emerald Blocks they point into, which in turn power the Note Blocks sitting directly on top of them. Because the Emerald Block is directly beneath the Note Block, it also changes the instrument sound to an 8-bit chiptune synthesizer.
- Pitch Tuning: Every time you right-click a note block, its pitch rises by one semitone (half-step), cycling through two full octaves (0 to 24 clicks).
Tips & variations
- Hiding the Instrument Blocks: If you don't want the Emerald Blocks sticking out above the floor, dig a 1-block-deep trench for the Emerald Blocks, place the Note Blocks at floor level on top of them, and run the repeaters directly into the sides of the Note Blocks.
- Simplifying the Trigger: In survival mode, if you don't have Nether Quartz for an observer, you can replace the silent note block starter with a simple wooden or stone Button.
- Longer Note Holds: The Tetris opening only uses quarter notes (4 ticks) and eighth notes (2 ticks), so a single repeater fits between every block. If your custom song uses half notes (8 ticks) or whole notes (16 ticks), place two or four repeaters in a row between those note blocks.
- Changing Tempo: Standard 1/2/4 tick spacing gives 150 BPM. Doubling all repeater delays (2/4/8 ticks) slows the song down to 75 BPM. For ~120 BPM or triplets (112 BPM), use 3 ticks for eighth notes and 6 ticks for quarter notes (note that you lose sixteenth notes at that resolution).
- Custom Instruments: Swap out the Emerald Blocks underneath the note blocks for other materials (like Gold Blocks for bells, Iron Blocks for iron xylophone, or Wood for bass guitar) to change the sound of your song.


