Redstone Light Switch

This simple redstone light switch lets you control lighting in your Minecraft base using two dedicated buttons: a green button to turn the light on, and a red button to turn it off. Unlike a single button that only powers a lamp briefly, this circuit uses a memory latch to keep the light on or off until you press the opposite button. It is a cheap, survival-friendly build that you can easily expand to control all the lights in a house.

Displays & LightingBeginnerBedrock Edition
Redstone Light Switch video tutorial

Video: MCPE 0.16.1: Redstone Tutorial - Light Switch! by MrCrayfish

How to build it

  1. Place the Control Blocks and Buttons

    Place your Red Wool block on the ground and stack the Green Wool block directly on top of it. Attach a Stone Button to the front face of both the red and green wool blocks.

  2. Build the Latch Frame

    Walk around to the back of the wool column. Place one solid building block to the left (next to the red wool) and another block behind it, then leave a two-block gap to the side and place a third building block on the ground.

  3. Attach the Redstone Torches

    Take your two Redstone Torches and mount them on the inside faces of the two outer building blocks so the torches face each other across the two-block gap.

  4. Wire the Latch Loop

    Place one Redstone Dust on the ground beside the first torch, and run two pieces of Redstone Dust over the top of the adjacent building blocks. On the other side of the loop, place two pieces of Redstone Dust on the ground between the blocks and one piece on top of the far building block so each torch powers the block holding the opposite torch.

  5. Position the Redstone Lamp

    Place one piece of Redstone Dust directly on top of the Green Wool block. Next, crouch and place your Redstone Lamp on top of the upper Stone Button (sitting directly in front of the top of the green wool).

  6. Connect the Lamp Output

    Climb up and place your final piece of Redstone Dust right on top of the Redstone Lamp. Press the green button to turn the lamp on and the red button to shut it off.

How it works

This contraption works by using a classic redstone memory circuit called an RS NOR latch, built from two opposing redstone torches:

  • Turning the Light On: When you press the top button on the Green Wool, it sends a pulse into the adjacent redstone dust line. This powers the block holding the first redstone torch, turning that torch off.
  • Locking the State: Once the first torch turns off, it stops powering the dust leading to the second torch's block. This allows the second redstone torch to turn on, which powers the wire leading back to the first torch—keeping it locked off—while also sending power up the Green Wool to keep the Redstone Lamp lit.
  • Turning the Light Off: Pressing the bottom button on the Red Wool powers the opposite side of the circuit. This turns off the active torch, allowing the first torch to turn back on and cut power to the lamp line.

Tips & variations

  • House Lighting: Instead of placing a single Redstone Lamp directly above the button, you can extend the output redstone line on top of the Green Wool into your ceiling to toggle an entire room of lamps at once (add repeaters if the wire exceeds 15 blocks).
  • Button Types: Either stone or wooden buttons work without issue because the latch flips immediately on the rising edge of the pulse.
  • Common Mistake: Make sure each redstone torch is attached to the side of a block that receives power from the opposite torch's redstone dust; if the dust does not run directly into or on top of the block holding the torch, the latch will not lock.

Frequently asked questions

Why use two buttons instead of a single lever?
A two-button RS NOR latch clearly separates the ON and OFF states with color-coded blocks, and it makes it easy to wire multiple ON or OFF buttons from different rooms into the same circuit.
Does this light switch work in Java Edition too?
Yes. Although demonstrated in Pocket/Bedrock Edition 0.16.1, basic redstone torch RS NOR latches and redstone lamps behave the same way in Java Edition.
How do I connect more than one Redstone Lamp to this switch?
Extend the redstone dust from the top of the Green Wool block along your ceiling or walls to reach additional lamps, placing a Redstone Repeater every 15 blocks to keep the signal strong.

Components used

More lamp switch / light control