
Video: ✔️ Minecraft: 8x8 Redstone House (FULL HOUSE TUTORIAL #1) by Twiistz
How to build it
- Frame the 8x8 Pillar Layout
Mark out an 8x8 area and place 4-block-tall oak log pillars at the corners and doorway frame. Connect the tops of the pillars using upside-down stone slabs, then extend the pillar tops by one block using six-sided oak wood and connect the roof trim with horizontal oak logs.
- Build the Modern Walls and Roof Trim
Fill the side wall with right-side-up and upside-down stone stairs alongside glass panes, and build the back wall out of white concrete. Wrap right-side-up stone slabs and smooth quartz slabs around the upper exterior gap to create a modern overhang, leaving a 1x2 doorway opening at the front.
- Dig the Item Elevator Shaft
Stand in the doorway, walk 4 blocks inside, and dig down 2 blocks to place the upper collection chest facing the wall. From beneath that chest, excavate a 6-block-deep shaft down to the basement level and clear a working room around the bottom.
- Wire the Auto-Dropper Clock
At the bottom of the item shaft, place an upward-facing dropper with a hopper feeding into it. Run a comparator out of the dropper into a repeater, which powers a sticky piston pushing an observer into a second observer; wire redstone dust from the observer output back to the dropper so it pulses automatically whenever items enter.
- Create the Soul Sand Bubble Column
Encase the space above the upward dropper in a 1x1 glass tube reaching the top floor, placing a hopper at the top pointing into your floor chest. Place water at the top, plant kelp from the bottom all the way up to convert the stream into water sources, break the kelp, and swap the bottom block for Soul Sand.
- Place the Hipster Door Pistons
Excavate 9 blocks deep under the doorway for the door wiring. Directly below the 1x2 doorway opening, place two upward-facing sticky pistons vertically (a double piston extender) and a third upward-facing sticky piston beside the top one, with two white concrete door blocks resting on top.
- Wire the 2x1 Hipster Door Circuit
Build the support block loop around the pistons and place 3 redstone dust along the bottom line with two repeaters set to 3 ticks and 4 ticks. Add upward-facing observers and a downward-facing observer to trigger the final retraction pulse, plus an observer reading the bottom redstone dust pointing into the side piston.
- Add the Dropper-Hopper T Flip-Flop
Behind the door's input block, place a repeater running out of a comparator that reads a dropper-hopper T flip-flop (one dropper facing horizontally into a downward dropper, which feeds an upward dropper via a bottom hopper). Place a single random item inside the loop so each pulse toggles the door open or closed.
- Install the Hidden Hopper Minecart Input
Under the corner floor block outside the entrance, dig 3 blocks down and stack a chest, a hopper, a rail, and a minecart with hopper enclosed by blocks so it cannot roll away. Take a comparator output from the hopper beneath the minecart, boost it with a repeater, and run redstone dust into the top dropper of your T flip-flop.
- Finish the Interior, Elevator, and Basement
Cover the floor with white concrete and stone brick slabs, leaving a trapdoor over the item elevator chest. Partition the back bedroom to house the compact vertical player elevator leading down to the basement mining room, where the minecart item conveyor and basement super smelter are installed.
How it works
This tiny house connects four separate survival circuits inside an 8x8 footprint:
- Auto-Dropper Item Elevator: When mined items are unloaded into the basement hopper line, they enter the upward-facing dropper. The
redstone-comparatordetects the inventory and powers asticky-pistonvia a repeater, pushing twoobserverblocks face-to-face. This observer clock rapidly fires the dropper into the Soul Sand bubble column until empty, shooting items straight into the upstairs hopper and chest. - Hidden Item Input & T Flip-Flop: Dropping any item onto the designated floor corner lets the concealed
hopper-minecartpull it right through the solid floor block into a hopper below. A comparator detects the passing item and sends a brief pulse into the 3-dropper, 1-hopper T flip-flop, shifting the internal item to toggle a constant signal on or off. - 2x1 Hipster Door: When the T flip-flop turns on, the 3-tick and 4-tick repeaters sequence the vertical double piston extender and side helper piston to push two white concrete blocks completely flush from below the floor. Turning the T flip-flop off de-powers the line while the
observerarray fires the extra downward and upward retraction pulses needed to pull both door blocks back underground.
Tips & variations
- Converting Water Sources: When building the item elevator, always place water on the block below the top glass rim so it flows horizontally into the collection hopper, then plant
kelpall the way from the bottom to the top before placing the Soul Sand—bubble columns require every block to be a full source block. - Securing the Hopper Minecart: Surround the input
hopper-minecartwith solid blocks before breaking any temporary scaffolding so you do not accidentally nudge it off its rail. - Observer Orientation: Double-check the arrow directions on the 4 observers inside the 2x1 hipster door; if one arrow points the wrong way, the top white concrete block will stay stuck in the doorway during retraction.

