What is Strong vs Weak Power?
When you run a redstone signal into a solid opaque block like stone or dirt, that block becomes "powered"—similar to having electricity running through it. However, Minecraft treats that electrified block differently depending on what put the power into it.
First, do not confuse strong and weak power with signal strength (the 0 to 15 power level that fades over distance). A block can be weakly powered at signal strength 15, or strongly powered at signal strength 1. Instead, strong and weak power describe which components can draw a signal out of the block:
- Strong Power (Hard Power): The block is energized by a power component (like a lever or redstone torch beneath it), a repeater, or a comparator. It is fully charged and will pass its signal to adjacent redstone dust, repeaters, comparators, and mechanisms.
- Weak Power (Soft Power): The block is energized only by redstone dust. It can still activate adjacent mechanisms (like pistons or lamps) and can still have its signal pulled out by a repeater or comparator, but it cannot power adjacent redstone dust.
Exact Rules of Block Powering
To predict how any circuit will behave, follow these strict game rules governing block power:
- Only opaque blocks can be powered: Full solid blocks (stone, cobblestone, wool) and opaque mechanism blocks (dispensers, droppers, note blocks, command blocks, redstone lamps) can hold strong or weak power.
- Transparent blocks cannot be powered: Glass, slabs, stairs, fences, walls, hoppers, pistons, and doors can never be strongly or weakly powered.
- No block-to-block transmission: An opaque block can never directly power another adjacent opaque block, even if it is strongly powered. There must always be dust or a redstone component between them.
- Power level does not drop inside a block: Signal strength (1 to 15) only decays by 1 during dust-to-dust transmission. Passing power from dust into a block, or from a strongly powered block back into dust, does not reduce its signal strength.
- Powered vs. Activated: An opaque mechanism like a redstone lamp is activated (turns on) when adjacent to a power source or powered block. However, it is only powered (able to pass signals to a repeater or dust) if the signal is fed directly into it as strong or weak power.
Step-by-Step Comparison Build
You can see the exact difference between strong and weak power in thirty seconds by building this small side-by-side test in Creative mode:
- Place two Redstone Lamps on the ground with a 2-block gap between them. (Redstone lamps are opaque blocks that light up when activated, making them great test blocks).
- Behind the first lamp, place a Redstone Repeater pointing directly into it, then place a lever behind the repeater.
- Behind the second lamp, place a piece of Redstone Dust pointing directly into it, then place a lever behind the dust.
- On the left side of both lamps, place a Redstone Repeater facing away from the lamp.
- On the right side of both lamps, place a piece of Redstone Dust.
- Flip both levers on.
The Result: Both redstone lamps light up, and both repeaters on the left turn on. However, on the right side, only the dust next to the first lamp lights up. The first lamp is strongly powered by the repeater, so it powers the dust. The second lamp is weakly powered by the dust behind it, so it activates the repeater on its left but refuses to power the dust on its right.
How Players Use It in Circuits
Redstoners exploit the rules of strong and weak power in nearly every contraption:
- Preventing Wire Cross-Talk: Because dust only weakly powers blocks, you can run a line of redstone dust over or alongside solid blocks without accidentally powering another dust line touching the other side of those blocks.
- Vertical Torch Towers: A redstone torch strongly powers the solid block directly above it (to power level 15). If you attach a second torch to that upper block, the strong power turns the second torch off. Stacking alternating blocks and torches creates a fast, compact 1x1 vertical signal wire.
- Powering Through Walls: If you want a clean floor or wall without visible redstone dust, you can point a repeater into a wall block (strongly powering it) and place redstone dust on the hidden side, or run dust into the wall (weakly powering it) and pull the signal out the back with a repeater.
- Multi-Way Splitters: Driving a repeater into a solid block strongly powers it, allowing you to draw full level 15 power out of the top, bottom, left, right, and front of that block simultaneously using redstone dust.
Common Mistakes to Avoid
- Expecting dust to go through a block into more dust: Beginners often run redstone dust into a solid block and place more dust on the other side, wondering why the signal stops. Because dust only applies weak power, you must replace either the input dust or the output dust with a repeater.
- Trying to power a torch attached to glass or slabs: Because walls, fences, glass, slabs, hoppers, and stairs are transparent and cannot be powered, any redstone torch attached to them can never be turned off.
- Thinking a torch strongly powers blocks beside it: A redstone torch only strongly powers the block directly above it. It will activate mechanisms next to or below it, and power dust next to or below it, but it does not power solid blocks adjacent to its sides or underneath it.
- Trying to chain two solid blocks together: Placing two stone blocks next to each other and running a repeater into the first one will never power a piston or dust touching the second block.
