4-Way Double Rail Intersection

This 4-way double rail intersection lets minecart riders stop at a junction and press one of three wooden buttons to travel left, straight, or right. All the redstone wiring is hidden underneath a central 5x5 roundabout loop, keeping the surface clean and easy to decorate for survival rail networks.

Minecart & Rail CircuitsIntermediateJava Edition
4-Way Double Rail Intersection video tutorial

Video: Minecraft - IMPROVED! - 4-Way Double Rail Intersection by CobblestoneAndDirt

How to build it

  1. Build the 5x5 Central Loop

    Lay out a 5x5 square of building blocks one level lower than your main rail network and place normal rails around the perimeter to form a central loop.

  2. Add the Four Double-Track Branches

    On all four sides of the 5x5 loop, extend two parallel lines of blocks outward by 4 blocks (spaced 1 block apart, matching the blocks adjacent to the corners) and step the 4th block up by one level to meet your main tracks.

  3. Lay the Powered Rails

    Place powered rails along the four straight blocks of each incoming and outgoing branch so they slope down into the central loop, then cap the upper end with a regular rail. Do not connect the T-junctions on the loop yet.

  4. Set Default Rail Switch Directions

    At all eight points where the branches meet the 5x5 loop, place a block one level below with a redstone torch on top, then place the junction rails. We want every rail switch to default to curving toward its closest corner of the 5x5 loop.

  5. Adjust Directional Rail Switches

    Because of Minecraft's directional rail rules, some switches will point the wrong way when powered. If an inbound switch is wrong, simply remove the torch underneath it; if an outbound switch needs inverting, move the torch to the side of the block under the rail and invert it with another torch below.

  6. Place the Rider Selection Buttons

    At each of the four incoming tracks (where the minecart stops on the slope), place three blocks adjacent to the sloped powered rail—one on the right side, one on the inner left side, and one further forward on the inner left—and put wooden buttons on top of all three.

  7. Isolate the Right-Turn Buttons

    Place a solid block directly beneath each of the four outer right-turn buttons. Because the default rail positions already curve around the nearest corner to the right, this button only needs to power the sloped rail next to it to launch the cart.

  8. Wire the Go-Straight Buttons

    From the block under each 'straight' button, step blocks down and run redstone dust directly into the block holding the torch for the first outbound switch around the loop. Pressing this button flips that single switch so the cart travels straight across.

  9. Wire the Left-Turn Buttons

    From beneath each 'left' button, place a repeater running into the block under the right-turn button to power the 'straight' line's switch while preventing back-feed. Also branch the dust downward and run a line with a repeater over to the next outbound switch around the loop so both switches flip together.

  10. Power the Outbound Tracks

    Place a constant power source (such as a redstone torch underneath) to keep the four outbound powered rail lines permanently active, leaving the four inbound slopes unpowered until a button is pressed.

How it works

When an incoming minecart enters the intersection, it rolls onto the unpowered sloped powered-rail and comes to a stop within reach of three wooden buttons:

  • Turn Right: All eight rail junctions on the 5x5 loop default to curving toward their nearest corner. Pressing the right button simply powers the sloped rail beside it, launching the cart around the first corner and immediately out the right-hand branch without toggling any switches.
  • Go Straight: Pressing the straight button powers the sloped rail and sends a signal to invert the first outbound junction. The cart enters the loop, passes straight past the right turn, and exits across the intersection on the next branch.
  • Turn Left: Pressing the left button powers the sloped rail and sends a signal through a redstone-repeater into the first junction's line while also routing a second line to the next outbound junction. Both switches flip temporarily, allowing the cart to travel around two sides of the 5x5 loop before exiting on the left branch.

Using wooden buttons instead of stone buttons is essential because their longer pulse duration keeps the second switch flipped long enough for the minecart to travel around the loop.

Tips & variations

  • Incoming Cart Speed: The intersection is dropped one block lower than the main track so incoming carts stop on the downward slope. If your carts come in very fast, keep the top flat rail as an unpowered powered rail to act as an extra brake. If speeds vary wildly, drop the intersection two blocks down to create a two-block slope.
  • Button Type: Always use wooden buttons. Stone buttons turn off too quickly, causing the second switch on a left turn to revert before the minecart reaches it.
  • Center Decorations & Delay: Placing solid blocks directly adjacent to the inner loop rails for decoration can slightly slow down the minecart on turns. You can adjust the tick delay on the repeaters along the longer left-turn lines to match your cart's travel time.

Frequently asked questions

Why do I have to use wooden buttons instead of stone buttons?
Wooden buttons stay active for 1.5 seconds (15 redstone ticks) compared to 1 second for stone buttons, giving the minecart enough time to travel halfway around the 5x5 loop before the second rail switch resets on a left turn.
Why don't all four corners use the exact same redstone torch placement?
Curved rails follow the South-East rule in Minecraft, meaning their default powered and unpowered directions depend on their cardinal orientation. Checking each corner with a torch first lets you invert only the switches that curve the wrong way.
What if my minecart stops too early or rolls right through the buttons?
Adjust the braking rails right before the slope. Use an unpowered powered rail at the top of the slope to slow down fast carts, or replace it with a normal rail if slow carts aren't reaching the sloped braking rail.

Components used

More rail switch